Using the Live view and setting up a wall display

The Live view (page title Tap Activity) shows scans as they happen. A rider's scan lights up their stop on the map within a few seconds. It's designed to run all day on a TV or wall monitor, and it works just as well in a browser tab.

Open it with Live view ▸ at the top right of the Historical Reports page, or go straight to https://my-tap-reports.myavail.cloud/live.

The Live view.

What's on the screen

Header

The Live view header.
Item Meaning
Scans Today Scans this screen has seen today: the hour before it was opened, plus everything since. If you open it mid-afternoon, it doesn't include the morning. For the official daily count, use Today on the Historical Reports page.
Last Hour Scans in the last 60 minutes.
Last 10 Min Scans in the last 10 minutes.
Top Stop The stop with the most scans that this screen has seen today.
◂ Historical Reports Goes back to the Historical Reports page.
Clock The current time in your agency's time zone.
Connection light Hover over it to see Connected or Reconnecting…. While it's reconnecting, new scans pause. When it reconnects, it fills in any scans it missed.
Sound button Off by default. Click it (tooltip Enable sound) to play a short chime for each scan. Click again (Mute sound) to turn it off. Browsers only allow sound after someone clicks on the page, so a wall display stays silent until someone clicks the button. The setting is remembered in that browser.

Map

  • Each scan makes its stop glow and sends out a ring. Orange is QR, cyan is NFC.
  • Repeated scans at a stop stack up, so a busy stop glows brighter and bigger. The glow fades over the following minutes.
  • The map is for display only and doesn't pan or zoom. It shows your service area.

Scan feed (right side)

  • The top card shows the newest scan: New scan · QR or New scan · NFC, the stop name, and how long ago it was (just now, 45s ago, 3m ago).
  • Earlier scans are listed below it. Each one shows the stop ID and a tag: ✓ location with the rider's distance from the stop (e.g. 248ft) for a QR scan where the rider allowed location, or — no location otherwise. NFC taps always show — no location.
  • Unknown stop means the scan had no stop, usually a QR rider who didn't allow location.

Activity strip (bottom)

Last 60 Minutes: one bar per minute, split into QR and NFC. It shows the rhythm of the last hour at a glance.

What's normal

  • A quiet screen overnight or early in the morning. If nobody is scanning, nothing lights up, and the counters can stay at 0 for long stretches.
  • Counters reset at midnight agency time.
  • Different numbers from Historical Reports. Scans Today only counts what the screen has seen since it was opened (plus the hour before). Historical Reports counts the whole day.

Setting up a wall display

A normal sign-in lasts 12 hours. A wall display has nobody around to sign in again, so myTap Reports gives a long-lasting sign-in to a browser that signs in through the Live view address.

What you need

  • A PC or TV stick with a current browser (Microsoft Edge or Google Chrome), connected to the screen.
  • A Microsoft account with access to myTap Reports. Use a shared operations account if your agency has one. If it belongs to a person, the display stops working when they leave or their access is removed.
  • A network that allows the sites listed in Troubleshooting myTap Reports, under "Network requirements".

Steps

  1. On the display computer, open a browser window that isn't already signed in to myTap Reports (a fresh browser profile works well).
  2. Go to exactly https://my-tap-reports.myavail.cloud/live. Don't start from the Historical Reports page and click Live view ▸, because that gives a normal 12-hour sign-in.
  3. Sign in with the account. The Live view for your agency opens.
  4. Click the sound button if you want chimes.
  5. Press F11 for full screen.
  6. In the computer's power settings, set the screen and sleep to Never. If the computer sleeps, the Live view stops updating.
  7. Optionally, set the browser to open https://my-tap-reports.myavail.cloud/live on startup, so the display recovers after a restart or power cut.

Check that it worked

  1. Hover over the connection light: it should say Connected.
  2. During service hours, scan a myTap QR code or tap an NFC tag at a stop. It should appear in the scan feed within about 5 seconds.
  3. The next day, check that the display is still updating without anyone signing in.

Related Content

Was this article helpful?

Articles in this section

New to the Help Center?
Review the Help Center guide
Help Center Feedback
Have a suggestion for new content or how we can improve the Help Center? Let us know!