Troubleshooting My Tap Reports

Start here

  1. Reload the page (F5). Most temporary problems clear on a reload.
  2. Check the date range at the top of Historical Reports. Many "missing data" questions come from looking at Today early in the morning.
  3. Check the exact message on screen and find it in the table below.

Quick reference

What you see Most likely cause Go to
"You do not have access to any agencies in myTap Reports. Contact Avail support if you believe this is a mistake." Your account hasn't been given access No access
Microsoft sign-in says your account doesn't exist or you need permission Wrong account, or you haven't accepted the invitation Can't sign in
"Could not determine your agency access. Please try again later." A temporary problem checking your access Access check failed
A card shows Data unavailable That report didn't load in time Data unavailable
Agency name reads CATA (Demo Data), or "Could not reach the backend — showing demo agencies." The page couldn't reach the server Demo Data showing
Zeros everywhere, or No stop activity in this period. No scans in the selected range No data or low numbers
Live view shows nothing, or the connection light says Reconnecting… Quiet period, or the network is blocking the live connection Live view not updating
Grey map with no streets, or blank charts Your network blocks a site the page needs Network requirements
Wall display asks for a sign-in again It was set up without the long-lasting sign-in Wall display signed out
Numbers on Live view and Historical Reports don't match They count different time windows Numbers don't match
An alert keeps coming back, or a colleague sees alerts you don't Acknowledging is per browser Understanding myTap Alerts

No access

The message shown to an account without access.

How to recognize it

  • After signing in you see: "You do not have access to any agencies in myTap Reports. Contact Avail support if you believe this is a mistake." with a Sign out link.
  • Or the agency page reads "You do not have access to any agencies."

Fix

  1. Check that you signed in with your work account, not a personal Microsoft account. If not, click Sign out and sign in again with the right account.
  2. If it's the right account, ask Avail support to give it access to your agency. Include the email address you sign in with.

Check that it worked

Access changes take effect within about 15 minutes. Reload the page, or sign out and in again, to see the change straight away.

Can't sign in

How to recognize it

  • The Microsoft sign-in page says your account doesn't exist in the directory, or that you need an administrator's approval.

Fix

  1. Look for an invitation email from Microsoft on behalf of Avail Technologies and accept it. You only need to do this once.
  2. Use the same email address the invitation was sent to.
  3. If your agency's IT blocks sign-in to outside organizations, ask them to allow it, or contact Avail support.

Access check failed

How to recognize it

  • "Could not determine your agency access. Please try again later."

Fix

This is a temporary problem on Avail's side. Wait a few minutes and reload. If it continues for more than 30 minutes, contact Avail support.

Data unavailable

The User Agents card showing Data unavailable. The rest of the page is still correct.

How to recognize it

  • One or more cards say Data unavailable instead of a chart or number. Other cards load normally.

Why it happens

Each card asks the server for its own report. If a report takes too long, which is most likely with 90d or long Custom ranges, the page tries again a couple of times and then shows Data unavailable for that card only.

Fix

  1. Wait a minute and reload the page.
  2. If you're using 90d or a long custom range, try 30d first. Once that loads, try the longer range again.
  3. If the same card fails every time for an hour or more, contact Avail support.

"Demo Data" showing

How to recognize it

  • The agency name under the page title reads CATA (Demo Data) (your agency code, followed by "(Demo Data)").
  • Or the agency page shows "Could not reach the backend — showing demo agencies."

What it means

The page couldn't load your agency's details from the server, so it fell back to placeholder settings. Don't use what's on screen. The map position and stop list may not be your agency's.

Fix

Reload the page after a minute. If it keeps happening, check your network connection (see 8. Network requirements) and then contact Avail support.

No data or low numbers

How to recognize it

  • Tiles show 0, charts are empty, or Per-Stop Detail reads No stop activity in this period.

Normal reasons

  • Today early in the morning, before service starts.
  • A Custom range from before your agency's myTap signs were installed.
  • A holiday or service suspension.

Fix

  1. Click 7d. If there's data there, nothing is wrong. The range you were looking at just had no scans.
  2. To check that scans are being recorded, open the Live view during service and test-scan a sign. It should appear within about 5 seconds.
  3. If the Live view stays empty during busy service hours and a test scan doesn't appear, contact Avail support.

Large "No stop selected" row

This is normal. It counts QR scans where the rider didn't allow location, so no stop could be recorded. These scans are still included in Total Scans.

Live view not updating

How to recognize it

  • Nothing new appears in the scan feed for a long time during service hours.
  • Hovering over the connection light at the top right shows Reconnecting….

Fix

  1. Remember that quiet periods are normal, especially overnight.
  2. If the light shows Reconnecting… for more than a minute, reload the page.
  3. If it never shows Connected on your network but works on a phone hotspot, your network is cutting off long-running connections. Ask your IT team to allow streaming ("server-sent events") from my-tap-reports.myavail.cloud without buffering or timeouts.
  4. Make sure the computer isn't going to sleep.

Network requirements

If your agency filters web traffic, the following sites must be allowed for the pages to work fully (verified November 2026):

Site Used for What breaks if blocked
my-tap-reports.myavail.cloud The reports themselves Everything
login.microsoftonline.com Sign-in You can't sign in
unpkg.com Map software Pages stop loading: cards stay grey and the Live view stays blank
cdn.jsdelivr.net Chart software Charts show Data unavailable
*.tile.openstreetmap.org Street map images Maps are grey with no streets (scan glow may still show)

Wall display signed out

How to recognize it

  • The wall display shows the Microsoft sign-in page, usually about 12 hours after it was set up.

Fix

Sign in through the Live view address so the display gets a long-lasting sign-in. Follow Using the Live view and setting up a wall display, "Setting up a wall display". The key step is to go directly to https://my-tap-reports.myavail.cloud/live while signed out, not to click Live view ▸ from the reports page.

A long-lasting sign-in also ends if the browser's data is cleared, the account's password is reset or its access is removed.

Numbers don't match

Comparison Why they differ
Live Scans Today vs Historical Today The Live view counts only what it has seen since it was opened, plus the hour before. Historical Reports counts the whole day. Use Historical Reports for official figures.
Unique Devices tile vs adding up the Unique Riders chart A phone that scans on several days counts once in the tile but once per day in the chart.
Per-stop scans add up to less than Total Scans Check the No stop selected row at the bottom of the table. It holds the scans without a stop.
Numbers change slightly on reload Your browser keeps reports for up to 5 minutes. A reload after that fetches the latest scans.
Times look an hour or more off All times are in your agency's local time zone, not your computer's.

When to contact Avail support

Contact Avail support if a fix above didn't help, and include:

  • Your agency and the email address you sign in with.
  • The full address from your browser's address bar. It includes the date range you were looking at.
  • The exact message on screen, or the name of the card showing Data unavailable.
  • A screenshot, the date and time it happened, and your browser (Edge, Chrome, Safari…).
  • For a sign problem: the stop name and ID, QR or NFC, and the alert text.

Never send passwords or sign-in codes in a ticket.

Related Content

Was this article helpful?

Articles in this section

New to the Help Center?
Review the Help Center guide
Help Center Feedback
Have a suggestion for new content or how we can improve the Help Center? Let us know!